new explosion idea
Moderators: Admin, Moderator Team
new explosion idea
i just figured out a way to set of an electricly charged explosion that can be used as a land mine if covered with flour
1. get paper caps (ones used in cap guns)
2. uncoil them
3. get a thin sewing needle
4. poke the needle threw the middle of each individual cap in the roll (should look like an accordian on the needle)
5. compact the accordian of caps with scotch tape so it is very little
6. wrap thick wire around both ends of the needle
7. take the other two ends
8. open the hood of your car
9. touch the ends of the stripped wire to your car battery
10. the caps make one big bang
if anyone has any ideas to elaborate on this or to make this into a squib please reply
p.s. : this works, i tried it
p.s.s.: i also posted this in special effects
1. get paper caps (ones used in cap guns)
2. uncoil them
3. get a thin sewing needle
4. poke the needle threw the middle of each individual cap in the roll (should look like an accordian on the needle)
5. compact the accordian of caps with scotch tape so it is very little
6. wrap thick wire around both ends of the needle
7. take the other two ends
8. open the hood of your car
9. touch the ends of the stripped wire to your car battery
10. the caps make one big bang
if anyone has any ideas to elaborate on this or to make this into a squib please reply
p.s. : this works, i tried it
p.s.s.: i also posted this in special effects
-
- Member
- Posts: 70
- Joined: Wed May 21, 2003 7:11 am
- Location: Australia
- Contact:
-
- Posting Freak
- Posts: 476
- Joined: Fri Jul 18, 2003 5:42 pm
- Location: New Brighton, Liverpool, England
- Contact:
-
- Moderator
- Posts: 2982
- Joined: Tue Dec 03, 2002 3:24 am
- Location: Ballarat, Victoria, Australia
- Contact:
I don't think the effect will be grand enough for a landmine. Hookin it up to the car That reminds me of the old trick of filling a gerrycan 2/3rds full of petrol, screwing a sparkplug into the cap, sealing it then hooking one of your cars sparkplug leads from the engine onto it. Guy turns the ignition on, sparkplug sparks the vapors and POW Or so i am informed
-
- Moderator
- Posts: 2030
- Joined: Fri Jul 18, 2003 8:37 pm
- Location: Esher, Surrey, Land Of Hope And Glory
- Contact:
If you lot want to mess aroud with spark plugs, you will need a coil to give the extra current to make the spark, otherwise you'll get nothing if you hjust hook it up to the battery! In fact, instead of a spark plug, you may as well have 2 wires close to each other.
Last edited by El Brenty on Sun Jan 11, 2004 3:25 pm, edited 1 time in total.
cant u just take some gunpowder, but it in foil, crumple it, stick a firecracker in it light it and throw it, insta boom right?
[url=http://profile.xfire.com/xerojohny88][img]http://miniprofile.xfire.com/bg/bg/type/0/xerojohny88.png[/img][/url]
--
Dance Dance Revolution: Proving white people dont have rhythm since 1998
--
Dance Dance Revolution: Proving white people dont have rhythm since 1998
The caps will go off wwith a bang about equivalent to a 1" or 1.5" firecracker. The trick is to wrap several layers of tape around the accordian, and make sure it is as compressed as possible. Wrap the tape before you take the caps off the needle. I always preferred using a large "diaper Pin" to pierce the caps since it gives a wider flash hole, allowing it to hit all the powder quicker. After removing the accordian from the pin, place several layers of tap over the bottom, attach the fuse/ ignitor over the hole on the top, and then tape that up well. If it is compressed tightly enough it will go bang. Just be careful though to pierce the caps straight on and gently. If you scrape the needle across the cap it could go foo and could ignite the others on the roll, remember caps are imact, friction sensitive .
The UNDERGROUND
[url]http://theundergroundtv.com[/url]
Music television for unsigned bands
[url]http://theundergroundtv.com[/url]
Music television for unsigned bands
-
- Forum Addict
- Posts: 921
- Joined: Fri Jan 09, 2004 4:07 pm
- Location: Bartow, Florida
- Contact:
I tryed what you said raptor. the first time the friction went POW but the second time it worked. I would advise what raptor said. it worked
"They're people who only want to be involved in filmmaking to get rich, get famous, or get laid. They know as much about filmmaking as George W. Bush knows about hand-to-hand combat"- Jim Jarmusch
-
- Forum Addict
- Posts: 921
- Joined: Fri Jan 09, 2004 4:07 pm
- Location: Bartow, Florida
- Contact:
It's in one of my posts above dude, the ignotor or fuse gets taed to the top cap directly over the hole created by the pin. It's not just wires though. You need to either use nichrome wire or very thin copper wire as the actual ignitor element. The wores just carry the current to the ignitor. If the wire is to thick it won't get hot enough to flash. Nichrome will flash at a lot lower current ( requiring a smaller battery ) than the copper will and is generally sold at hobby stores for use in model rocket ignitors. Model rocket ignitors, while a little more expensive than bare nichrome, are a very affordable way to get good reliable ignition. For instructions on creating the ignitors, see CamClubs post on the ignitor, and I believe Grant had posted a squib article that included instructions for the same type of resistance wire ignitor.Famous wrote:WHERE DO THE WIRES GO?
The UNDERGROUND
[url]http://theundergroundtv.com[/url]
Music television for unsigned bands
[url]http://theundergroundtv.com[/url]
Music television for unsigned bands